Security Seals
Welcome to BatteryMart.com!Thank you for choosing us for your battery needs. Click Here >>

Smart Charger

Showing 1 - 24 of 40 items Search Results for "smart charger"

1 2 of 2 next

Sort By:

BM Part #:
ACC-CH-V2299

Quantity
Price: 27.95
  • Voltage: 12 Volt
  • Warranty: 6 Months
Recharges batteries in all capacities: 2-4pcs AAA, AA, C, D and 1-2pcs 9V. NiCd & NiMH batteries can be mixed to charge at the same time. Features: Easy to use Plugs into your wall's electrical outlets with the supplied AC adapter when using at your home or office or by the supplied 12VDC car adapter for use in your vehicle's cigarette plug. Recharges NiMH and NiCd batteries. Two (2) to four (4) pieces of high capacity AA, AAA, C and D or one (1) to two (2) pieces of 9V, at a time. The battery life is well protected by the -dV detection and timer protection for AA, AAA, C, and D size batteries. Automatic charging current selection for the different sizes of batteries. LED display for rapid charger, trickle charge, and bad cell detection for AA, AAA, C, and D size batteries. RED LED: Rapid Charge GREEN LED: Cells are ready for use / Trickle Charge Flashing RED LED: Cells are not suitable for charging For 9V Batteries: RED LED: Charging Safety Features: Negative delta V cut-off function Safety time to prevent over charge Short circuit protection Reverse-polarity protection Bad cell detection Estimated Charging times: AAA size: Capacity: 600 - 900 mAh Charging time: 1.5 - 3 hrs. AA size: Capacity: 800 - 2500 mAh Charging time: 1- 3 hrs. C size: Capacity: 1200 - 4500 mAh Charging time: 2 - 7 hrs. D size: Capacity: 1200 - 9000 mAh Charging time: 2- 14 hrs. 9V block size: Capacity: 100 - 200 mAh Charging time: 9-17 hrs.
(Learn More)
BM Part #:
01025

Quantity
Price: 21.95
  • Voltage: 6 Volt - 12 Volt
  • Capacity (Amp Hours): 1 Amp / 2 Amp
  • Warranty: 1 Year
Best Charger for charging all RC Car, RC Airplane and Airsoft battery packs 6V, 7.2V, 8.4V, 9.6V, 10.8V and 12V Patent pending watchdog technology provides maximum safety Universal for any NiMH /NiCd battery packs 6V - 12V (5-10 Cells Pack) Fast charger with current switch to select either 1A or 2A Charging Current 1A for battery packs with capacity from 1000mAh -1800mAh Charging Current 2A for battery packs with capacity above 2000mAh. For 3000mAh pack, charging time is apprx. 1.5 hours Smart Charger with automatic voltage detection Temperature sensor to protect battery pack from over heating Use pulse and negative pulse technology to avoid battery overheating during fast charging, optimized for battery pack's cycle life Red LED will be on during charging Automatically charging ending with negative delta V Worldwide usage with 120-240V AC Includes: 1 standard Tamiya connector with Temperature Sensor. 1 adapter from standard Tamiya to Mini Tamiya. 1 adapter from standard Tamiya to a pair of alligator clip. Smart Charger Specification FOR 6V-12V NiMH/NiCD Battery Packs 5-10 Cells Packs Input: AC 100-240V Output: 6-12V, 1A or 2A Operation Instruction Connect battery pack to output connector and plug AC power source Make sure battery polarity is connected correctly (Red wire is positive) Charger will detect battery voltage automatically, Red LED will be on during charging When battery is fully charged, current will reduce to trickle charging at 50mA, Green LED will be on Battery will be charged at 1A or 2A constant current (selectable) Approximate Charging time is about 1.5hrs for 3000mAh battery,1hr for 1800mAh battery The charger is designed for faster charging NiCd and NiMH battery packs from 6 to 12V for RC car/Air and Air soft gun Don't charge battery packs with voltage less than 6V or greater than 12V and capacity smaller than 1000mAh or larger than 5000mAh Battery pack must be made by high drain current cell Please contact your seller for instruction. Mfg is not responsible for any damage and consequent damage by Misuse.
(Learn More)
BM Part #:
01027

Quantity
Price: 21.95
  • Voltage: 12V - 24V
  • Capacity (Amp Hours): 500 mA
  • Warranty: 1 Year
Best Charger for charging all RC Car, RC Airplane and Airsoft battery packs 12V - 24V. Universal for any NiMH /NiCd battery packs 12V - 24V (10-20 Cells pack). 100-240V AC input for worldwide use - 500mA charging current. Designed for use with 12V - 24V battery packs (please don't charge battery pack under 12V or over 24V). Green LED will flash slowly when no battery is plugged in, Red LED will be on during charging. Green LED will be on when battery is fully charged. Red LED will rapidly flash when the charger is short circuit, Red LED will flash if polarity is reversed or the battery is non-rechargeable. Automatically cut-off by negative delta V detecting or when battery's temperature is over 60˚C; when battery pack gets fully charged, Green LED will be on. 15-hour safety timer, charger will stop charging after operates 15 hours. One standard Tamiya male connector installed with the charger. One set of alligator clip adapter with female tamiya connector included for charging other type of battery packs. One adapter from standard male Tamiya to mini female Tamiya for charging airsoft gun battery packs. Includes: 1 standard Tamiya connector. 1 connector adapter from standard Tamiya to Mini Tamiya. 1 set of alligator clip adapter with standard Tamiya connector on one end. 1 Temperature sensor. Smart Charger Specification Input: AC100-240V Output: 12-24V Charging Current (Normal Charging): 0.5A±10% @CV=10V-32V Operation Instruction Connect battery pack to output connector and plug AC power source. Make sure battery polarity is connected correctly (Red wire is positive). Put the temperature sensor onto the middle surface of battery pack with rubberized fabric (refer to the following temperature sensor usage demonstration). When charger is connected to the AC source, the green LED flash. After charger is connected to correct battery pack, the red LED will be on to show that it is charging.
(Learn More)
BM Part #:
CH-011

Quantity
Price: 224.95
  • Voltage: 10.8 Volt
  • Warranty: 1 Year
This two bay sequential smart charger is designed to charge the smart SM-Bus "DR" series batteries, including DR35AAS, DR36AAS, DR201, DR202, DR202I, and DR202X.
(Learn More)
BM Part #:
APSCHL

Quantity
Price: 25.95
Primary Advantages: LCD Display Individual Fast Charger Absolutely Safe& Smart USB Charging Function 100V-240V World Wide Voltage Main Features: Easy to Read LCD Display (Shows charging progress, defective battery and battery refresh function) 4 Individual Charging Channels Super Quick Charger 6-Level Charge Protection Delta V/0 Delta V cut off Over Temperature Protection(60°) Timer Control Protection (6.5 Hours) Reverse Polarity Protection Over Current and Short Circuit Protection Defective and Non-rechargeable battery detection Low Current Leakage Minimizes loss of capacity and maintains charging of battery by Controlling Current Leakage Trickle Charge to Maintain Battery Charge Worldwide Voltage 100V-240V Battery Rescue Function Pulse and Series Charging Technology for Fast and Efficient Charging Battery REFRESH Function and Reduce Memory Effect and Enable Full Discharge for Longer Battery Life Powered by AC Outlet /USB 5.0VDC Specifications: Adapter Input: AC adapter 110V-240VAC, 50/60 Hz, 5W Output: 5VDC - 800mA Charger (Electronic SCH600F) Charging current: AA/R06 or AAA/R03*2:1000mA; AA/R06 or AAA/R03*4: 500mA Environmental Conditions: Ambient Temperature 0° to 40°/ Best at 25+/-2° Storage temperature -20° to 60° / Best at 25+/-5° Humidity 5% to 85%/ non condensing Charging Times Battery Type Battery Capacity Approximate Charging time 1-2PCS 3-4PCS R03/AAA Ni-MH 900mAh 1.1hrs 2.2hrs R03/AAA Ni-MH 800mAh 0.96hr 1.9hrs R06/AA Ni-MH 2500mAh 3.0hrs 6.0hrs R06/AA Ni-MH 2000mAh 2.4hrs 4.8hrs R06/AA Ni-MH 1800mAh 2.2hrs 4.3hrs *When the batteries are fully charged, the charger will automatically switch to a minimum maintenance charge if the batteries are not immediately removed from the unit. *Charge time stated is for a full charge on fully discharged batteries.
(Learn More)
BM Part #:
GEN2-MINI

Quantity
Price: 106.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 4 Amp per Bank
The GEN Mini On-Board Battery Charger is a rugged and compact waterproof charger for 12V lead acid batteries. It can be mounted onto virtually any vehicle, such as a boat, car, tractor, or RV. Safe to leave connected indefinitely; the GEN Mini interactively diagnoses, recovers, and charges Wet, Gel, MF and AGM batteries chemistries from 20-120Ah and maintains all battery sizes. Wicked Smart Features FULLY INTERACTIVEAutomatically adjusts itself to changing current needs DESIGNED FOR SAFETYReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent & overcharge HF/HE SWITCH MODE DESIGNHigh-frequency, high-efficiency for lightweight, compact charger RAPID CHARGING TECHNOLOGYCharges batteries 2X faster than traditional linear battery chargers VARIABLE INPUT COMPENSATED100% full charge even with varying A/C input voltages RECOVERY MODERecovers deeply discharged & sulfated batteries with pulse charging MULTIPLE BATTERY CHEMISTRYSafely charges Wet, Gel, MF & AGM batteries ABNORMALITY PROTECTIONAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time WATERPROOF100% completely sealed. Protects our units from the most extreme environments and rated at IP68 SPECIFIC GRAVITY OPTIMIZATIONA stabilizing charge that optimizes the specific gravity of a battery for increased performance IGNITION PROTECTEDNon-igniting and temperature controlled for safe and worry-free operation
(Learn More)
BM Part #:
01269-01

Quantity
Price: 16.95
  • Warranty: 1 Year
The TN269 charger offers one of the fastest charge rates for Li-Ion Cylindrical batteries on the market in a compact design. Capable of fully charging your 18650 batteries in 2-3 hours you spend less time waiting. With smart automatic charging, independent charging channels, & reverse polarity protection the TN269 is a feature rich portable charger with significant value. If you have or plan to use the rechargeable cylindrical Li-Ion batteries, the TN269 is your go-to charger & is one of the most popular charging choices amongst our customers. Features and Benefits: Worldwide Voltage: 110-240V AC Two independent charging channels for individual charging & detection Fast Charge Rate: 1A (1,000mah)/per hour charges 2600mah battery in approximately 2.5 hours Constant current and constant voltage charging mode Reverse polarity protection: automatically terminates charging & LED flashes red when the polarity is reversed Compact design & portable Specifications Input: DC 12V 1000mA Output: DC 4.2V 1000mA per channel Supports the following Rechargeable Li-Ion Battery Sizes: 186501850014500 DC barrel connector dimension: 5.5 x 2.1 x 10 Warning Don't disassemble the charger Don't charge other types of battery. It may cause explosion and breakage The charger is only for in-house using and should be kept away from heat surrounding Keep the charger away from humidity circumstances and no liquid is allowed to get in, otherwise it may cause damage and lead to accident It should be placed out of children's reach It may not be able to fully charge those batteries which have not been used for a long time. Several recycles of charge-discharge will improve the battery's performance * Please carefully read the instruction before using!
(Learn More)
BM Part #:
021-1162

Quantity
Price: 19.95
  • Warranty: 3 Year Factory Direct
Not for use with the Battery Tender solar panels. A controller is built in to Battery Tender panels. Battery Tender Solar Controller allows you to convert an existing solar panel into a solar charger using Battery Tender patented Super Smart Charging Algorithm. Usable input range between 5-45 Watts! Product Features Convert any existing solar panel into a solar charger Battery Tender Solar Controller has a usable input range between 5-45 watts Fully automatic: Prevents your battery from either overcharging or undercharging Keeps the excess voltage from damaging the battery
(Learn More)
BM Part #:
PS68

Quantity
Price: 10.95
  • Capacity (Amp Hours): 400 mAh
Rayovac On-The-Go Charger: Plug it in and you're instantly powered up! Charge your Apple or micro-USB device for any emergency situation. This innovative product by Rayovac includes a detachable micro-USB and built-in Apple device connector, making it compatible with over 90% of the smartphone in use today. Features: Up to an additional 45 minutes on your cell/smart phone. 400 mA lithium ion rechargeable battery. Use and recharge 100s of times. Keychain attached for a portable and convenient instant power solution. No cords needed. How to Use: To charge the On-The-Go Charger's internal battery: Set the switch to the "IN/OFF" position and plug it into any computer USB port. The LED will light up red and will change to green when charging is complete. To charge your device, such as a cell phone: Set the switch to "OUT" and use the appropriate plug to plug it into your phone or other chargeable device. The device should show that it's charging.
(Learn More)
BM Part #:
G26000

Quantity
Price: 284.95
  • Voltage: 12/24 Volt
  • Capacity (Amp Hours): 12V @ 26 Amps / 24V @ 13 Amps
The G26000 is a smart, 15 Step, fully automatic switch-mode battery charger and maintainer. The G26000 restores batteries to their original capacity, recovers slightly sulfated batteries, charges batteries in cold climates, rescues drained batteries, and provides maintenance charging to increase battery life. A powerful battery charger with specialized charging modes for recovering severely drained batteries that will not accept a normal charge and the ability to perform an equalization charge. The G26000 comes equipped with a remote temperature probe for optimized charging performance. Suitable for most 12V and 24V battery capacities from 25-500Ah, such as Motorcycles, ATVs, UTVs, Snowmobiles, Jet Skis, Cars, RVs, Boats and Trucks. var playedOnce = false; function onYouTubePlayerReady(playerid) { player = document.getElementById('ytvideo'); player.addEventListener('onStateChange', 'youtubeEvent'); } function youtubeEvent(state) { if (state == 1) { if (!playedOnce) { playedOnce = true; _gaq.push(['_trackEvent', 'Videos', 'Unique_Play_Per_Page', 'G26000']); } _gaq.push(['_trackEvent', 'Videos', 'Play', 'G26000']); return; } if (state == 0) { _gaq.push(['_trackEvent', 'Videos', 'Ended', 'G26000']); return; } } Powered by NOCO VosFX Processor The VosFX Processor is a revolutionary smart processor utilizing sophisticated levels of intelligence to alter the charge process, based on organic feedback from the battery, to extend battery life. The VosFX Processor quickly and efficiently makes decisions on how to charge the battery without risking user safety or damage to the battery. Wicked Smart Features: 12V/24V CompatibilityCharges 12V and 24V batteries Auto-memoryReturns to last selected mode when restarted Fully InteractiveAutomatically adjusts itself to changing current needs Designed for SafetyReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent, and overcharge Multiple Battery ChemistrySafely chargers Wet, Gel, MF, and AGM batteries Extendable ConnectorsPlug-n-play connectors for easy accessory changes HF/HE Switch Mode DesignHigh-frequency, high-efficiency for a lightweight, compact charger Rapid Charging TechnologyCharges batteries 2X faster than traditional linear battery chargers Variable Input Compensated100% full charge even with varying A/C input voltages Abnormality ProtectionAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time Recovery ModeRecovers deeply discharged & sulphated batteries with pulse charging Cold/AGM ModeOptimized charge mode for cold weather or AGM batteries 16V and 32V Boost ModeHelps recover deeply discharged or sulphated batteries for 12V & 24V 13.6V Equalization and Supply ModeCharge mode for maximizing battery capacity, reviving low voltage batteries & can act as a power supply Calcium ModeCharge mode designed for calcium batteries Silent Night ModeDisables the charger's internal fan for quiet nighttime operation What's in the box? G26000 Charger HD Battery clamp connectors HD Eyelet Terminal Connectors Owner's manual and user guide (View PDF) Charging Steps Step 1: Diagnostics Checks the battery voltage to make sure battery connections are good and the battery is in a stable condition before beginning the charge process. Step 2: Recovery Initializes the Recovery process, if needed, for deeply discharged or sulfated (desulfation) batteries by pulsing small amounts of current. Step 3: Soft Start Begins Bulk charging process with a gentle (soft) charge. Step 4-7: Bulk The Bulk charging process continues using Max Rate, High Rate, Medium Rate and Low Rate charges and returns 80% of battery capacity, indicated by the 25%, 50% and 75% CHARGE LEDs. Step 8: Absorption Brings the charge level to 90%. The battery charger will deliver small amounts of current to provide a safe, efficient charge and limit battery gassing. Step 9: Trickle Battery is fully charged and ready to use, indicated by the 100% CHARGE LED being a solid Green. In this step, the battery charger will only deliver enough current to keep the battery full. If the battery tells the charger that more current is needed, the battery charger will switch to Maintenance. Step 10: Maintenance Continuously monitors the battery voltage to determine if a Maintenance charge should be initiated. If the terminal voltage falls below 12.8V (12V) and 25.6V (24V), the charger will start the Maintenance cycle until voltage reaches 14.4V (12V) and 28.8V (24V) and then discontinues the charge cycle. The cycle between Trickle and Maintenance is repeated indefinitely to keep the battery at full charge, without overcharging. The battery charger can be left connected indefinitely. Step 11: 13.6V Supply The 13.6V SUPPLY mode is used for low voltage batteries, maintenance charging or as a power supply. Step 12: 13.6V Equalization The 13.6V EQUALIZATION is used to provide an equalization charge by delivering a constant voltage of 13.6V. Step 13: Silent Night The SILENT NIGHT is used to provide quiet operation by reducing the charging current to 5A (5000mA) and disabling the internal cooling fan. Step 14: 16V Boost The 16V BOOST mode is used to recover battery capacity from a stratified (sulfated) battery by applying a specialized high 16.5V (17V Max) voltage to soften and melt down sulfate from the battery plates so that the material becomes usable again. Step 15: 32V Boost The 32V BOOST is used to recover battery capacity from a stratified (sulfated) battery by applying a specialized high 33V (34V Max) voltage to soften and melt down sulfate from the battery plates so that the material becomes usable again.
(Learn More)
BM Part #:
G7200

Quantity
Price: 99.95
  • Voltage: 12/24 Volt
  • Capacity (Amp Hours): 12V @ 7.2 Amps / 24V @ 3.6 Amps
The G7200 is a smart, 12 Step, fully automatic switch-mode battery charger and maintainer. The G7200 restores batteries to their original capacity, recovers slightly sulfated batteries, charges batteries in cold climates, rescues drained batteries, and provides maintenance charging to increase battery life. A powerful battery charger with specialized charging modes for recovering severely drained batteries that will not accept a normal charge. Suitable for most 12V and 24V battery capacities from 14-230Ah, such as Motorcycles, ATVs, UTVs, Snowmobiles, Jet Skis, Cars, RVs, Boats and Trucks. var playedOnce = false; function onYouTubePlayerReady(playerid) { player = document.getElementById('ytvideo'); player.addEventListener('onStateChange', 'youtubeEvent'); } function youtubeEvent(state) { if (state == 1) { if (!playedOnce) { playedOnce = true; _gaq.push(['_trackEvent', 'Videos', 'Unique_Play_Per_Page', 'G7200']); } _gaq.push(['_trackEvent', 'Videos', 'Play', 'G7200']); return; } if (state == 0) { _gaq.push(['_trackEvent', 'Videos', 'Ended', 'G7200']); return; } } Powered by NOCO VosFX Processor The VosFX Processor is a revolutionary smart processor utilizing sophisticated levels of intelligence to alter the charge process, based on organic feedback from the battery, to extend battery life. The VosFX Processor quickly and efficiently makes decisions on how to charge the battery without risking user safety or damage to the battery. What's in the box? G7200 Charger Battery clamp connectors Eyelet Terminal Connectors Owner's manual and user guide (View PDF) Wicked Smart Features: 12V/24V CompatibilityCharges 12V and 24V batteries Auto-memoryReturns to last selected mode when restarted Fully InteractiveAutomatically adjusts itself to changing current needs Designed for SafetyReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent, and overcharge Multiple Battery ChemistrySafely chargers Wet, Gel, MF, and AGM batteries Extendable ConnectorsPlug-n-play connectors for easy accessory changes HF/HE Switch Mode DesignHigh-frequency, high-efficiency for a lightweight, compact charger Rapid Charging TechnologyCharges batteries 2X faster than traditional linear battery chargers Variable Input Compensated100% full charge even with varying A/C input voltages Abnormality ProtectionAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time Recovery ModeRecovers deeply discharged & sulphated batteries with pulse charging Cold/AGM ModeOptimized charge mode for cold weather or AGM batteries 16V Boost ModeHelps recover deeply discharged or sulphated batteries 13.6V Supply ModeCharge mode for maximizing battery capacity, reviving low voltage batteries & can act as a power supply Charging Steps Step 1: Diagnostics Checks the battery voltage to make sure battery connections are good and the battery is in a stable condition before beginning the charge process. Step 2: Recovery Initializes the Recovery process, if needed, for deeply discharged or sulfated (desulfation) batteries by pulsing small amounts of current. Step 3: Soft Start Begins Bulk charging process with a gentle (soft) charge. Step 4-7: Bulk The Bulk charging process continues and returns 80% of the battery capacity. Indicated by the 25%, 50% and 75% CHARGE LEDs. Step 8: Absorption Brings the charge level to 90%. The battery charger will deliver small amounts of current to provide a safe, efficient charge and limit battery gassing. Step 9: Trickle Battery is fully charged and ready to use, indicated by the 100% CHARGE LED being a solid Green. In this Step, the battery charger will only deliver enough current to keep the battery full. If the battery tells the charger that more current is needed, the battery charger will switch to Maintenance. Step 10: Maintenance Continuously monitors the battery voltage to determine if a Maintenance charge should be initiated. If the terminal voltage falls below 12.8V (12V) and 25.6V (24V), the charger will start the Maintenance cycle until voltage reaches 14.4V (12V) and 28.8V (24V) and then discontinues the charge cycle. The cycle between Trickle and Maintenance is repeated indefinitely to keep the battery at full charge, without overcharging. The battery charger can be left connected indefinitely. Step 11: 13.6V Supply The 13.6V SUPPLY mode is used for low voltage batteries, maintenance charging or as a power supply. Step 12: 16V Boost The 16V BOOST mode is used to recover battery capacity from a stratified (sulfated) battery by applying a specialized high 16.5V (17V Max) voltage to soften and melt down sulfate from the battery plates so that the material becomes usable again. Technical Specifications: Input Voltage AC: 110-120VAC, 50-60Hz Working Voltage AC: 85-130 VAC, 50-60Hz Input Current: 2000mA RMS Max Efficiency: 85% Approx. Power: 150W Max Charging Voltage: 14.4/28.8V, 14.7/29.4V (Cold/AGM), 13.6V (Supply), 16.5V (Boost) Charging Current: 7200mA (12V), 3600mA (24V), 5000mA (Supply), 1500mA (Boost) Back Current Drain: <5mA Ripple: <2% Charger Type: 12 Step, Fully Automatic, Switch-Mode Type of Batteries: 12V & 24V Lead-Acid Battery Chemistries: Wet, Gel, MF & AGM Battery Capacity: 14-230Ah (12V), 14-120Ah (24V) Housing Protection: IP65 Cooling: Natural Convection Noise Level: <50 dB Dimensions (L x W x H): 8.9 x 3.8 x 2.4 Inches Weight: 1.7 Pounds
(Learn More)
BM Part #:
G1100

Quantity
Price: 44.95
  • Voltage: 6/12 Volt
  • Capacity (Amp Hours): 1.1 Amps
The G1100 is a smart, 7 Step, fully automatic switch-mode battery charger and maintainer. The G1100 is best for small battery applications from 2.2-40Ah, such as charging your Motorcycle, ATV, Jet Ski or Snowmobile. In addition to charging, the G1100 can effectively maintain any 6V or 12V batteries in larger applications, such as Cars, RVs, Boats and Trucks. var playedOnce = false; function onYouTubePlayerReady(playerid) { player = document.getElementById('ytvideo'); player.addEventListener('onStateChange', 'youtubeEvent'); } function youtubeEvent(state) { if (state == 1) { if (!playedOnce) { playedOnce = true; _gaq.push(['_trackEvent', 'Videos', 'Unique_Play_Per_Page', 'G1100']); } _gaq.push(['_trackEvent', 'Videos', 'Play', 'G1100']); return; } if (state == 0) { _gaq.push(['_trackEvent', 'Videos', 'Ended', 'G1100']); return; } } Powered by NOCO VosFX Processor The VosFX Processor is a revolutionary smart processor utilizing sophisticated levels of intelligence to alter the charge process, based on organic feedback from the battery, to extend battery life. The VosFX Processor quickly and efficiently makes decisions on how to charge the battery without risking user safety or damage to the battery. Wicked Smart Features: 6V/12V CompatibilityCharges 6V and 12V batteries Auto-memoryReturns to last selected mode when restarted Fully InteractiveAutomatically adjusts itself to changing current needs Designed for SafetyReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent, and overcharge Multiple Battery ChemistrySafely chargers Wet, Gel, MF, and AGM batteries Extendable ConnectorsPlug-n-play connectors for easy accessory changes HF/HE Switch Mode DesignHigh-frequency, high-efficiency for a lightweight, compact charger Rapid Charging TechnologyCharges batteries 2X faster than traditional linear battery chargers Variable Input Compensated100% full charge even with varying A/C input voltages Abnormality ProtectionAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time Recovery ModeRecovers deeply discharged & sulphated batteries with pulse charging Cold/AGM ModeOptimized charge mode for cold weather or AGM batteries What's in the box? G1100 Charger Battery clamp connectors Eyelet Terminal Connectors Owner's manual and user guide (View PDF) Charging Steps Step 1: Diagnostics Checks the battery voltage to make sure battery connections are good and the battery is in a stable condition before beginning the charge process. Step 2: Recovery Initializes the Recovery process, if needed, for deeply discharged or sulfated (desulfation) batteries by pulsing small amounts of current. Step 3: Soft Start Begins Bulk charging process with a gentle (soft) charge. Step 4: Bulk The Bulk charging process continues and returns 80% of the battery capacity. Indicated by the 25%, 50% and 75% CHARGE LEDs. Step 5: Absorption Brings the charge level to 90%. The battery charger will deliver small amounts of current to provide a safe, efficient charge and limit battery gassing. Step 6: Trickle Battery is fully charged and ready to use, indicated by the 100% CHARGE LED being a solid Green. In this Step, the battery charger will only deliver enough current to keep the battery full. If the battery tells the charger that more current is needed, the battery charger will switch to Maintenance. Step 7: Maintenance Continuously monitors the battery voltage to determine if a maintenance charge should be initiated. If the terminal voltage falls below 6.4V (6V) and 12.8V (12V), the charger will start the Maintenance cycle until voltage reaches 7.2V (6V) and 14.4V (12V) and then discontinues the charge cycle. The cycle between Trickle and Maintenance is repeated indefinitely to keep the battery at full charge, without overcharging. The battery charger can be left connected indefinitely. Technical Specifications: Input Voltage AC: 110-120VAC, 50-60Hz Working Voltage AC: 85-130 VAC, 50-60Hz Input Current: 600mA RMS Max Efficiency: 85% Approx. Power: 30W Max Charging Voltage: 7.2V/14.4V, 7.4/14.7V (Cold/AGM) Charging Current: 1100mA Back Current Drain: <5mA Ripple: <2% Charger Type: 7 Step, Fully Automatic, Switch-Mode Type of Batteries: 6V & 12V Lead-Acid Battery Chemistries: Wet, Gel, MF & AGM Battery Capacity: 2.2-40Ah, up to 150Ah for Maintenance Housing Protection: IP65 Cooling: Natural Convection Noise Level: <50 dB Dimensions (L x W x H): 6.1 x 2.5 x 1.6 Inches Weight: 0.8 Pounds
(Learn More)
BM Part #:
G750

Quantity
Price: 31.95
  • Voltage: 6/12 Volt
  • Capacity (Amp Hours): 750 mA
The NOCO G750 is a smart, 5 Step, fully automatic switch-mode battery charger and maintainer. The G750 is best for small battery applications from 1.2-30Ah, such as charging your Motorcycle, ATV, Jet Ski or Snowmobile. In addition to charging, the G750 can effectively maintain any 6V or 12V batteries in larger applications, such as Cars, RVs, Boats and Trucks. var playedOnce = false; function onYouTubePlayerReady(playerid) { player = document.getElementById('ytvideo'); player.addEventListener('onStateChange', 'youtubeEvent'); } function youtubeEvent(state) { if (state == 1) { if (!playedOnce) { playedOnce = true; _gaq.push(['_trackEvent', 'Videos', 'Unique_Play_Per_Page', 'G750']); } _gaq.push(['_trackEvent', 'Videos', 'Play', 'G750']); return; } if (state == 0) { _gaq.push(['_trackEvent', 'Videos', 'Ended', 'G750']); return; } } Powered by NOCO VosFX Processor The VosFX Processor is a revolutionary smart processor utilizing sophisticated levels of intelligence to alter the charge process, based on organic feedback from the battery, to extend battery life. The VosFX Processor quickly and efficiently makes decisions on how to charge the battery without risking user safety or damage to the battery. Wicked Smart Features: 6V/12V CompatibilityCharges 6V and 12V batteries Auto-memoryReturns to last selected mode when restarted Fully InteractiveAutomatically adjusts itself to changing current needs Designed for SafetyReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent, and overcharge Multiple Battery ChemistrySafely chargers Wet, Gel, MF, and AGM batteries Extendable ConnectorsPlug-n-play connectors for easy accessory changes HF/HE Switch Mode DesignHigh-frequency, high-efficiency for a lightweight, compact charger Rapid Charging TechnologyCharges batteries 2X faster than traditional linear battery chargers Variable Input Compensated100% full charge even with varying A/C input voltages Abnormality ProtectionAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time What's in the box? G750 Charger Battery clamp connectors Eyelet Terminal Connectors Owner's manual and user guide (View PDF) Charging Steps Step 1: Diagnostics Checks the battery voltage to make sure battery connections are good and the battery is in a stable condition before beginning the charge process. Step 2: Soft Start Begins Bulk charging process with a gentle (soft) charge. Step 3: Bulk Continues Bulk charging process, returns 90% of battery capacity. Step 4: Absorption Brings the charge level to 100%. The battery charger will deliver small amounts of current to provide a safe, efficient charge and limit battery gassing. Step 5: Maintenance Monitors the battery voltage continuously to determine if a maintenance charge should be initiated. If the terminal voltage falls below approximately 6.4V (6V) and 12.8V (12V), the charger will start the Maintenance cycle until voltage reaches approximately 7.2V (6V) and 14.4V (12V) and then will discontinue the charge cycle. Maintenance cycle is repeated indefinitely to keep the battery at full charge, without overcharging. The battery charger can be left connected indefinitely. Technical Specifications: Input Voltage AC: 110-120VAC, 50-60Hz Working Voltage AC: 85-130 VAC, 50-60Hz Input Current: 300mA RMS Max Efficiency: 85% Approx. Power: 20W Max Charging Voltage: 7.2V/14.4V Charging Current: 750mA Back Current Drain: <5mA Ripple: <2% Charger Type: 5 Step, Fully Automatic, Switch-Mode Type of Batteries: 6V and 12V Lead-Acid Battery Chemistries: Wet, Gel, MF & AGM Battery Capacity: 1.2-30Ah, Maintains All Battery Sizes Housing Protection: IP60 Cooling: Natural Convection Noise Level: <50 dB Dimensions (L x W x H): 4.5 x 2.7 x 1.3 Inches Weight: 0.5 Pounds
(Learn More)
BM Part #:
021-1164

Quantity
Price: 85.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 540 mAmps
  • Warranty: 5 Year Factory Direct
Harness the power of the sun!This Battery Tender product by Deltran is a 10-watt solar panel with built-in smart charging controller. This panel provides 100% portable battery charging and maintenance. Perfect when you lack traditional power access. Battery Tender solar panels are the only panels available with a built-in charge controller to prevent overcharging! Product Specifications: Amazing simple DIY installation 26" X 16" X 0.875" 5.5 lbs Built-in 3-step micro-controller for precise charging 12 V Nominal Voltage 540 mAmps Temperature Compensation Sensor Reverse polarity protected Sparkproof, waterproof: Excellent option for outdoor installations 5 Year Factory Direct Warranty (covers manufacturer defects only, not breakage)
(Learn More)
BM Part #:
021-1165

Quantity
Price: 118.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 830 mAmps
  • Warranty: 5 Year Factory Direct
Harness the power of the sun!This Battery Tender product by Deltran is a 15-watt solar panel with built-in smart charging controller. This panel provides 100% portable battery charging and maintenance. Perfect when you lack traditional power access. Battery Tender solar panels are the only panels available with a built-in charge controller to prevent overcharging! Product Specifications: Amazing simple DIY installation 38" x 16" x 0.875" 8 lbs Built-in 3-step micro-controller for precise charging 12 V Nominal Voltage 830 mAmps Temperature Compensation Sensor Reverse polarity protected Sparkproof, waterproof: Excellent option for outdoor installations 5 Year Factory Direct Warranty (covers manufacturer defects only, not breakage)
(Learn More)
BM Part #:
G3500

Quantity
Price: 59.95
  • Voltage: 6/12 Volt
  • Capacity (Amp Hours): 3.5 Amps
The G3500 is a smart, 8 Step, fully automatic switch-mode battery charger and maintainer. The G3500 restores batteries to their original capacity, recovers slightly sulfated batteries, charges batteries in cold climates, rescues drained batteries, and provides maintenance charging to increase battery life. A versatile battery charger that provides charging modes for both large and small batteries from 1.2-120Ah, such as Cars, RVs, Boats and Trucks, as well as for Motorcycles, ATVs, Jet Skis or Snowmobiles. var playedOnce = false; function onYouTubePlayerReady(playerid) { player = document.getElementById('ytvideo'); player.addEventListener('onStateChange', 'youtubeEvent'); } function youtubeEvent(state) { if (state == 1) { if (!playedOnce) { playedOnce = true; _gaq.push(['_trackEvent', 'Videos', 'Unique_Play_Per_Page', 'G3500']); } _gaq.push(['_trackEvent', 'Videos', 'Play', 'G3500']); return; } if (state == 0) { _gaq.push(['_trackEvent', 'Videos', 'Ended', 'G3500']); return; } } Powered by NOCO VosFX Processor The VosFX Processor is a revolutionary smart processor utilizing sophisticated levels of intelligence to alter the charge process, based on organic feedback from the battery, to extend battery life. The VosFX Processor quickly and efficiently makes decisions on how to charge the battery without risking user safety or damage to the battery. Wicked Smart Features: 6V/12V CompatibilityCharges 6V and 12V batteries Auto-memoryReturns to last selected mode when restarted Fully InteractiveAutomatically adjusts itself to changing current needs Designed for SafetyReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent, and overcharge Multiple Battery ChemistrySafely chargers Wet, Gel, MF, and AGM batteries Extendable ConnectorsPlug-n-play connectors for easy accessory changes HF/HE Switch Mode DesignHigh-frequency, high-efficiency for a lightweight, compact charger Rapid Charging TechnologyCharges batteries 2X faster than traditional linear battery chargers Variable Input Compensated100% full charge even with varying A/C input voltages Abnormality ProtectionAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time Recovery ModeRecovers deeply discharged & sulphated batteries with pulse charging Cold/AGM ModeOptimized charge mode for cold weather or AGM batteries What's in the box? G3500 Charger Battery Clamp Connectors Eyelet Terminal Connectors Owner's Manual & User Guide (View PDF) Product Registration Card Charging Steps Step 1: Diagnostics Checks the battery voltage to make sure battery connections are good and the battery is in a stable condition before beginning the charge process. Step 2: Recovery Initializes the Recovery process, if needed, for deeply discharged or sulfated (desulfation) batteries by pulsing small amounts of current. Step 3: Soft Start Begins Bulk charging process with a gentle (soft) charge. Step 4-5: Bulk The Bulk charging process continues using both a High Rate and Medium Rate charge and returns 80% of battery capacity, indicated by the 25%, 50% and 75% CHARGE LEDs. Step 6: Absorption Brings the charge level to 90%. The battery charger will deliver small amounts of current to provide a safe, efficient charge and limit battery gassing. Step 7: Trickle Battery is fully charged and ready to use, indicated by the 100% CHARGE LED being a solid Green. In this step, the battery charger will only deliver enough current to keep the battery full. If the battery tells the charger that more current is needed, the battery charger will switch to Maintenance. Step 8: Maintenance Continuously monitors the battery voltage to determine if a maintenance charge should be initiated. If the terminal voltage falls below 6.4V (6V) and 12.8V (12V), the charger will start the Maintenance cycle until voltage reaches 7.2V (6V) and 14.4V (12V) and then discontinues the charge cycle. The cycle between Trickle and Maintenance is repeated indefinitely to keep the battery at full charge, without overcharging. The battery charger can be left connected indefinitely. Technical Specifications: Input Voltage AC: 110-120VAC, 50-60Hz Working Voltage AC: 85-130 VAC, 50-60Hz Input Current: 1200mA RMS Max Efficiency: 85% Approx. Power: 60W Max Charging Voltage: 7.2V/14.4V, 7.4/14.7V (Cold/AGM) Charging Current: 3500mA (Large), 900mA (Small) Back Current Drain: <5mA Ripple: <2% Charger Type: 8 Step, Fully Automatic, Switch-Mode Type of Batteries: 6V & 12V Lead-Acid Battery Chemistries: Wet, Gel, MF & AGM Battery Capacity: 14-120Ah (Large), 1.2-14Ah (Small) Housing Protection: IP65 Cooling: Natural Convection Noise Level: <50 dB Dimensions (L x W x H): 7.7 x 2.7 x 1.9 Inches Weight: 1.1 Pounds
(Learn More)
BM Part #:
01322

Quantity
Price: 74.99
  • Capacity (Amp Hours): 5 Amp
  • Warranty: 1 Year
Tenergy TB6AC Dual Power Balancing Charger (with built-in AC Adaptor) is one of today's most advanced type of smart charger. The TB6AC can accept three types of Lithium batteries - LiIo, LiPo and LiFe. It offers additional Lithium programming. Fast charge reduces the charging time of the Lithium battery and the Storage mode controls the final voltage of the battery to be suit for long time storage. Also feature LCD display and High-quality aluminum case is durable and very efficient to cool out the internal heat. Multiple Charging Harnesses "Octopus" for TB6/TB6B/TB6AC Balance Charger (Valued over $10.99), are included for FREE! Charging Harness has the following connectors: Traxxas Tamiya Mini Tamiya JST Hitec EC3 Deans Specifications: Operating voltage: DC 11~18 volts Charge power: max. 50 Watts Discharge power: max. 5 Watts NiCd/MH: 1~15 cells LiIo/LiPo/LiFe: 1~6 series Pb: 2~20V Charge current: 0.1 to 5.0A Discharge current: 0.1 to 1.0A No. of cycle: 1 to 5 times Dimension: 5.28" Width x 5.59" Length x 1.42" Height Features: Temperature sensor port Built in AC adapter High-power and high-performance circuit The smart charger employs a circuit that has maximum output power of 50W. As a result, the smart charger can charge or discharge up to 15 cells of NiCd/NiMH and 6 series of Lithium batteries with maximum current of 5.0A. Individual voltage balancer for Lithium batteries inside Built into the smart charger is an individual-cell-voltage balancer. No external balancer is needed when charging Lithium batteries (LiIo/LiPo/LiFe) for balance charging. Balance individual cells on discharge The smart charger also can monitor and balance individual cells of the Lithium battery pack during the discharge process, as well as the charge process. If the voltage of any one cell varies abnormally, the process will be stopped with the error message. Accept various types of Lithium battery The smart charger can accept three types of Lithium batteries - LiIo, LiPo and LiFe. They have different characteristics by their chemistry, such as minimum, maximum, and charge termination voltages. Lithium battery Fast and Storage mode The smart charger offers additional Lithium programming. Fast charge reduces the charging time of the Lithium battery and the Storage mode controls the final voltage of the battery to be suit for long time storage. Data store/load 5 data of different batteries programs can be stored and retrieved. These data files can be recetrived at any time you need them without reprogramming. Cyclic charging/discharging The smart charger can perform 1 to 5 cycles of charge-discharge or discharge-charge for battery break in/refreshing and balancing. Back-light LCD screen Include LCD display Robust outer aluminum case High-quality aluminum case is durable and very efficient to cool out the internal heat Advanced temperature sensor cable port (sensor cable not included) An optional temperature probe contacting the surface of the battery to monitor the battery temperature during charging can be used.
(Learn More)
BM Part #:
021-0146-4

Quantity
Price: 459.95
  • Voltage: 12 Volt
  • Warranty: 3 Year Factory Direct
This item is Built-To-Order. Once this item is ordered, it cannot be canceled, returned, or exchanged. Please confirm that you need a 240 Volt unit before ordering. Safe, No Spark Charging! Deltran's advanced SuperSmart Battery Tender Battery Management System is light years ahead of any standard battery charger. It's the first fully automatic, constant-current battery charger designed to charge and/ or maintain up to 5 12-volt batteries simultaneously @ 2 amps.This Multiple Charging Station Shop Charger uses 5 independent Battery Tender Plus battery charger circuits in a single enclosure. Each circuit is a linear power converter that has a true DC output at a maximum power level of approximately 29 watts. It has a maximum output charging current of 2.0 amps. This is a higher current output than the stand-alone Battery Tender Plus battery charger circuits because each shop charger has an internal fan to provide forced air cooling of all active, semiconductor components.Includes 5 six foot Clamp HarnessesWill correctly charge and maintain any type of lead acid battery - AGM (absorbed glass mat), sealed calcium or Gel batteriesTo avoid dangerous dead-short sparking, microchip circuitry will not activate output voltage until clips are correctly connected to batterySimultaneously charges and/ or maintains up to 5 batteries or any combination from 1 to 5Maintains batteries at full chargeTemperature compensated to ensure optimum charge voltage according to ambient temperatureAutomatically switches from full charge to float charging mode. Reverse Polarity Protection to ensure no charger or battery damageComplete 4-step charging program (Qualification, Bulk Charge, Absorption Mode, Float Mode).BTP microchip technology virtually eliminates battery destroying sulfation Built in 72 hour timer will protect a marginal battery from over charging2 amps per output charging currentInput Power: 240 VAC @ 50HzTemperature Range: -20F to 120F Technical Specs: (Adobe PDF) (Microsoft Word)
(Learn More)
BM Part #:
021-0133

Quantity
Price: 398.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 2 Amps
  • Warranty: 3 Year Factory Direct
Safe, No Spark Charging! Deltran's advanced SuperSmart Battery Tender Battery Management System is light years ahead of any standard battery charger. It's the first fully automatic, constant-current battery charger designed to charge and/ or maintain up to 5 12-volt batteries simultaneously @ 2 amps.This Multiple Charging Station Shop Charger uses 5 independent Battery Tender Plus battery charger circuits in a single enclosure. Each circuit is a linear power converter that has a true DC output at a maximum power level of approximately 29 watts. It has a maximum output charging current of 2.0 amps. This is a higher current output than the stand-alone Battery Tender Plus battery charger circuits because each shop charger has an internal fan to provide forced air cooling of all active, semiconductor components.Includes 5 six foot Clamp HarnessesWill correctly charge and maintain any type of lead acid battery - AGM (absorbed glass mat), sealed calcium or Gel batteriesTo avoid dangerous dead-short sparking, microchip circuitry will not activate output voltage until clips are correctly connected to batterySimultaneously charges and/ or maintains up to 5 batteries or any combination from 1 to 5Maintains batteries at full chargeTemperature compensated to ensure optimum charge voltage according to ambient temperatureAutomatically switches from full charge to float charging mode. Reverse Polarity Protection to ensure no charger or battery damageComplete 4-step charging program (Qualification, Bulk Charge, Absorption Mode, Float Mode).BTP microchip technology virtually eliminates battery destroying sulfation Built in 72 hour timer will protect a marginal battery from over charging2 amps per output charging currentInput Power: 115VAC @ 60HzTemperature Range: -20F to 120F Technical Specs: (Adobe PDF) (Microsoft Word)
(Learn More)
BM Part #:
021-0134

Quantity
Price: 539.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 2 Amps
  • Warranty: 3 Year Factory Direct
Safe, No Spark Charging! Deltran's advanced SuperSmart Battery Tender Battery Management System is light years ahead of any standard battery charger. It's the first fully automatic, constant-current battery charger designed to charge and/ or maintain up to 10 12-volt batteries simultaneously @ 2 amps.This Multiple Charging Station Shop Charger uses 10 independent Battery Tender Plus battery charger circuits in a single enclosure. Each circuit is a linear power converter that has a true DC output at a maximum power level of approximately 29 watts. It has a maximum output charging current of 2.0 amps. This is a higher current output than the stand-alone Battery Tender Plus battery charger circuits because each shop charger has an internal fan to provide forced air cooling of all active, semiconductor components.Includes 10 six foot Clamp HarnessesWill correctly charge and maintain any type of lead acid battery - AGM (absorbed glass mat), sealed calcium or Gel batteriesTo avoid dangerous dead-short sparking, microchip circuitry will not activate output voltage until clips are correctly connected to batterySimultaneously charges and/ or maintains up to 10 batteries or any combination from 1 to 10Maintains batteries at full chargeTemperature compensated to ensure optimum charge voltage according to ambient temperatureAutomatically switches from full charge to float charging modeReverse Polarity Protection to ensure user safetyComplete 4-step charging program (Qualification, Bulk Charge, Absorption Mode, Float Mode)BTP microchip technology virtually eliminates battery destroying sulfationBuilt in 72 hour timer will protect a marginal battery from over charging2 amps per output charging currentInput Power: 115VAC @ 60HzTemperature Range: -20F to 120FTechnical Specs: (Adobe PDF)
(Learn More)
BM Part #:
021-0147-4

Battery Tender 12 Volt 2 Amp Battery Charger - 10 Banks 240 Volt AC Free Ground Shipping!
Made to Order - Ships in 7-10 Days
Quantity
Price: 584.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 2 Amps
  • Warranty: 3 Years Factory Direct
    (Returned units for repair may take 7 to 10 days for turn around time)
This item is Built-To-Order. Once this item is ordered, it cannot be canceled, returned, or exchanged. Please confirm that you need a 240 Volt unit before ordering. **No AC Plug Included with Charger** **Customer Must Supply Correct AC Plug & Install** Please see below. Safe, No Spark Charging! Deltran's advanced SuperSmart Battery Tender Battery Management System is light years ahead of any standard battery charger. It's the first fully automatic, constant-current battery charger designed to charge and/ or maintain up to 10 12-volt batteries simultaneously @ 2 amps.This Multiple Charging Station Shop Charger uses 10 independent Battery Tender Plus battery charger circuits in a single enclosure. Each circuit is a linear power converter that has a true DC output at a maximum power level of approximately 29 watts. It has a maximum output charging current of 2.0 amps. This is a higher current output than the stand-alone Battery Tender Plus battery charger circuits because each shop charger has an internal fan to provide forced air cooling of all active, semiconductor components.Includes 10 six foot Clamp HarnessesWill correctly charge and maintain any type of lead acid battery - AGM (absorbed glass mat), sealed calcium or Gel batteriesTo avoid dangerous dead-short sparking, microchip circuitry will not activate output voltage until clips are correctly connected to batterySimultaneously charges and/ or maintains up to 10 batteries or any combination from 1 to 10Maintains batteries at full chargeTemperature compensated to ensure optimum charge voltage according to ambient temperatureAutomatically switches from full charge to float charging modeReverse Polarity Protection to ensure user safetyComplete 4-step charging program (Qualification, Bulk Charge, Absorption Mode, Float Mode)BTP microchip technology virtually eliminates battery destroying sulfationBuilt in 72 hour timer will protect a marginal battery from over charging2 amps per output charging currentInput Power: 240 VAC @ 50HzTemperature Range: -20F to 120FTechnical Specs: (Adobe PDF) AC Plug not included. Customer must supply IEC Cord (Specification IEC 60320, C13 Line Socket): Device supplied with C14 chassis plug (inlet):
(Learn More)
BM Part #:
GEN1-MINI

Quantity
Price: 62.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 4 Amp
The GEN Mini On-Board Battery Charger is a rugged and compact waterproof charger for 12V lead acid batteries. It can be mounted onto virtually any vehicle, such as a boat, car, tractor, or RV. Safe to leave connected indefinitely; the GEN Mini interactively diagnoses, recovers, and charges Wet, Gel, MF and AGM batteries chemistries from 20-120Ah and maintains all battery sizes. Wicked Smart Features FULLY INTERACTIVEAutomatically adjusts itself to changing current needs DESIGNED FOR SAFETYReverse polarity, short circuit, open circuit, spark proof, overheat, overcurrent & overcharge HF/HE SWITCH MODE DESIGNHigh-frequency, high-efficiency for lightweight, compact charger RAPID CHARGING TECHNOLOGYCharges batteries 2X faster than traditional linear battery chargers VARIABLE INPUT COMPENSATED100% full charge even with varying A/C input voltages RECOVERY MODERecovers deeply discharged & sulfated batteries with pulse charging MULTIPLE BATTERY CHEMISTRYSafely charges Wet, Gel, MF & AGM batteries ABNORMALITY PROTECTIONAutomatically shuts "off" if charger remains in Bulk charge mode for an extended period of time WATERPROOF100% completely sealed. Protects our units from the most extreme environments and rated at IP68 SPECIFIC GRAVITY OPTIMIZATIONA stabilizing charge that optimizes the specific gravity of a battery for increased performance IGNITION PROTECTEDNon-igniting and temperature controlled for safe and worry-free operation
(Learn More)
BM Part #:
ACC-IC-109V

Quantity
Price: 32.95
  • Voltage: 9 Volt
  • Warranty: 3 Year
2-3 Hours Rapid Smart Battery Charger Compatible with our 9 Volt NiMH batteries. USE ONLY NIMH OR NICD BATTERIES. DO NOT USE ANY OTHER BATTERY TYPES. This will cause injury to device and person. Features: Automatically detects and fully charges NiCd and NiMH 9 Volt batteries Automatically switches to trickle charge mode when charge is complete Overcharge protection ensuring longer battery cycle life AC/DC adapter CSA, CE and UL Approved Per channel LED will be flashing and not charge if a defective cell is inserted Can charge any number of batteries at a time Suitable for 9 volt batteries from 7.2V to 9.6V You can mix charge NiCd and NiMH 9 volt batteries Specs: Includes External AC adapter; Input 120V - 240V 3 Year Warranty for Factory Defects 50Ma DC charge current in each slot LED lights turn to red for each battery when charging and off when complete Charge Times: NiCd 8.4V 120-140mAh 2.5 to 3 hours NiCd 7.2V 120-140mAh 2.5 to 3 hours NiMH 9.6V 160-200mAh 3.5 to 4 hours NiMH 8.4V 160-200mAh 3.5 to 4 hours
(Learn More)
BM Part #:
021-1163

Quantity
Price: 59.95
  • Voltage: 12 Volt
  • Capacity (Amp Hours): 270 mA
  • Warranty: 5 Year Factory Direct
Harness the power of the sun!This Battery Tender product by Deltran is a 5-watt solar panel with built-in smart charging controller. This panel provides 100% portable battery charging and maintenance. Perfect when you lack traditional power access. Battery Tender solar panels are the only panels available with a built-in charge controller to prevent overcharging! Product Specifications: Amazingly simple DIY installation 13.25" X 16" X 0.875" 3 lbs Built-in 3-step microcontroller for precise charging 12 V Nominal Voltage 270 mAmps Temperature Compensation Sensor Reverse polarity protected Sparkproof, waterproof: Excellent option for outdoor installations 5 Year Factory Direct Warranty (covers manufacturer defects only, not breakage)
(Learn More)
1 2 of 2 next
SearchSpring